# Question: What Does CP And CPK Tell You?

## What is a good CP value?

By convention, when a process has a Cp value less than 1.0, it is considered potentially incapable of meeting specification requirements.

Conversely, when a process Cp is greater than or equal to 1.0, the process has the potential of being capable.

Ideally, the Cp should be as high as possible..

## Why is it called 6 Sigma?

The name Six Sigma is derived from the bell curve used in statistics where one Sigma represents one standard deviation away from the mean. The defect rate is said to be extremely low when the process exhibits Six Sigma’s, where three are above the mean and three below.

## Why CP value is greater than CPK?

As you know, the greater the value of Cpk, the better is the capability of the process to produce parts within Specification. While only Process variation influences the Cp value, both Variation and central tendency influences Cpk. This is why Cp will always be greater than or equal to Cpk.

## How do you read CP and CPK?

If the overall average is in the center of the specification, the Cp and Cpk values will be the same. If the Cp and Cpk values are different, the overall average is not centrally located. The larger the difference in the values, the more offset the overall average. This concept is shown graphically below.

## How many Sigma is 1.67 Cpk?

Sigma level tableTwo sided tableCpk PpkSigma levelPPM out of tolerance1.334.063.3421.504.56.7951.675.00.5738 more rows

## What is minimum Cpk value?

The minimum value of “k” is 0 and the maximum is 1.0. A perfectly centered process will have Cp = Cpk. Both Cpk and Ppk relate the standard deviation and centering of the process about the midpoint to the allowable tolerance specifications. An estimate for Cpk = Cp(1-k).

## What does a Cpk of 1.67 mean?

The Capability Index, Cpk. The outcome of a Process Capability study is a single metric, which provides an indication of the ability of a process to consistently provide output which is within required specifications. CPK <1.00 (Poor, incapable) 1.00< CPK <1.67 (Fair) CPK >1.67 (Excellent, Capable)

## What does CPK stand for?

creatine phosphokinaseCPK is the abbreviation for a blood test called creatine phosphokinase. CPK is an enzyme found primarily in muscles. This includes the muscles in the heart. Any muscle injury or damage can cause a rise in the blood level of CPK.

## What is a good CP and CPK?

We generally want a Cpk of at least 1.33 [4 sigma] or higher to satisfy most customers. Cpk can have an upper and lower value reported. If the upper value is 2 and the lower is 1, we say it has been shifted to the left.

## What does a Cpk of 1.33 mean?

Cpk = or >1.33 indicates that the process is capable and meets specification limits. Any value less than this may mean variation is too wide compared to the specification or the process average is away from the target.

## What does a CP value mean?

Cp is a ratio of the specification spread to the process spread. The process spread is often defined as the 6-sigma spread of the process (that is, 6 times the within-subgroup standard deviation). Higher Cp values indicate a more capable process. … When the specification spread is less than the process spread, Cp is low.

## What is CPK and how is it calculated?

Cpk is a process capability index used to measure what a process is capable of producing. … The formula for the calculation of Cpk is Cpk = min(USL – μ, μ – LSL) / (3σ) where USL and LSL are the upper and lower specification limits, respectively.

## What is CP CPK value?

Cp and Cpk, commonly referred to as process capability indices, are used to define the ability of a process to produce a product that meets requirements. … Specifications are normally defined in terms of nominal (+/-) tolerances or ranges (low to high.

## What is a good CPK?

The higher the Cpk, the better is the capability of the process to meet its requirements. In the industry, a Cpk of less than 1.66 needs a closer look. A Cpk that’s less than 1.33 needs some action to make it higher, and a Cpk of less than 1.0 means that the process is not capable of meeting its requirements.

## What is CP CPK formula?

The equation for Cpk is more complicated: [minimum(mean – LSL, USL – mean)] / (0.5*NT). LSL stands for Lower Specification Limit and USL stands for Upper Specification Limit. Often we describe Cpk as the capability the process is achieving whether or not the mean is centered between the specification limits.

## What does a Cp of 1.5 mean?

A Cp of less than one indicates that the process spread is greater than the specification. This means that some of the data lies outside the specification. … So a Cp of 1.5 means the process can fit inside the specification 1.5 times. A Cp greater than one is obviously desirable.